Products

The SW-PY Series of screen ink is especially formulated for screen printing on pre-treated PE and PP packaging, where glossy finish and excellent chemical resistance properties are required. With recommended diluent, excellent screen stability enables the ink to be used on manual up to fully automatic printing machines, can be customize to suit most printing requirement Stencils : Solvent resistance direct photo emulsion DE442 or dual sensitized PU220 Universal photo emulsion, Coverage: Mileage of printing approximately 45 – 50 square meter per liter of ink with 120 T/cm ( 305 T / Inch ) mesh count monofilament Polyester or Nylon and 10% dilution.

UGI is a two-pack screen ink with outstanding resistance to many chemicals and solvents and excellent adhesion to a wide range of difficult to adhere to substrates, such as metal (including aluminum, copper, brass, tin coated metal and iron), glass, ceramic, plastic, mirror, Bakelite, Formica, Acrylic, Polyethylene (PE), pretreated Polypropylene (PP), Nylon and some Polyester. UGI gives good adhesion to substrates coated with resin, silicone and wax. To improve adhesion, the substrate should be cleaned with Thinner 2900 before printing. UGI is not suitable for printing outdoor displays which require long term weather stability.

POXY Series of screen ink is a 2-pot system, exhibits high gloss, chemical resistance and good adhesion when the print undergoes a mild stoving schedule. Catalyzed ink is highly recommended for finishing where excellent is demanded, with outstanding resistance to many chemicals and solvents and excellent adhesion to a wide range of difficult to adhere to substrates, such as metal (including aluminum, copper, brass, tin coated metal and iron), glass, ceramic, plastic, mirror, Bakelite, Formica, Acrylic, Polyethylene (PE), pretreated Polypropylene (PP), Nylon and some Polyester. PX is suitable for printing outdoor displays which require long term weather stability.

PPG is a solvent-based screen printing ink suitable for printing onto containers made from untreated or pretreated polypropylene. This ink system has a high gloss finish and excellent adhesion, giving it good rub-resistance. PPG can be printed through any type of mesh, but for the best printing results it is recommended that monofilament P90-48 to P120-34 be used.

• PPG can be printed through a variety of solvent resistant stencils, such as Diazol (PU220), and Diazol Fast (S42).
• 1Kg of ink will print an area of 65-75 m 2 through a P120-34 mesh.

PP is a gloss finish solvent-based, single-pack ink specially designed for printing pretreated polyethylene and polypropylene. When thinned, PP can be used with high-speed automatic or semi-automatic printing machines. PP is very fast drying and has excellent adhesion resulting in durable ink films with good resistance against a wide range of products including bleaches, motor oils and most detergents. However, PP is not resistant to cosmetics or products containing alcohol, such as certain lotions or perfumes. PP is also suitable for printing various types of aluminum. Please see “ the detail information in Metal printing.”

Can be printed through a variety of solvent resistant stencils, such as Diazol (S42), Polyzol direct DE422 and Diazol Universal PU20. A snap distance of about 2-3 mm is required for a good release of the print from the screen. Apply Spray Way SW82 all over the print table to firmly hold the substrate in place during printing. Due to the wide range of coatings available, it is advisable that the ink be tested fully prior to printing.

EA2000 is a gloss finish, solvent-based, one / two-pack ink specially formulated for printing pretreated polyethylene and polypropylene. EA2000 can be thinned for use with high-speed automatic or semi-automatic printing machines. These inks are very fast drying, have excellent adhesion and good resistance to a wide range of products such as bleaches, motor oils and most detergents. They are also resistant to cosmetics and products containing alcohol such as certain lotions and perfumes. EA2000 is also suitable for printing onto various types of aluminum as it is very fast drying and has excellent adhesion. Please see the section on “Metal printing”.

The BBP series of screen ink, with a range of opaque colors, is ideal for printing on PP Co-polymer and PP board, PP substrates – treated and untreated. It gives a satin to glossy finish and is suitable where chemical and scuff resistance requirement is not stringent. Drying Tack free in approximately 10-15 minutes. Forced dry at 40-60c in approximately 2-3 minutes. Coverage Approximately 45-50 square meter per liter of ink with 120 threads / cm. mesh count monofilament polyester or nylon and 10% dilution.